Better Health

Don Paris Ph.D. _

Newsletters by Dr. Don Paris

Click here to Sign Up

 
 

Mag pulse

What is "The Magnetic Pulser"?

The Magnetic Pulser is a professionally designed quality unit, thoroughly tested and guaranteed to operate as per the specifications. The Magnetic Pulser is designed to generate an intense (~6,000 Gauss*), momentary (~2.5mS) pulsed DC magnetic field. in Regular Mode and (2,500 Gauss) in Fast Mode.


*Magnetic flux intensity follows the inverse square rule - the further you are away from the magnetic core, the faster the Gauss intensity drops off. At face of Magnetic Coil, the Gauss is ~6,000 Gauss.


NOTE: Please do not confuse this unit with permanent/ceramic magnet therapies, or with the EMR (electro-magnetic radiation) producing units!
Through the principle of induction, this magnetic field creates eddy-currents (tiny electrical micro-currents). Designed to be used with The Silver Pulser or independently. Targets specific areas.


New Features of model MP6:

  • magentic pulseNew streamlined unit.
  • magentic pulseQuartz crystal Micro-Computer controlled functions for precise waveform generation and accurate timing sequences.
  • magentic pulseRed Light indicates when Magnetic Pulse has been delivered to the Hand paddle/Coil.
  • magentic pulseNew AUDIBLE output option. When selected, the MP6 will beep each time the Magnetic Pulse has been delivered to the Hand paddle/Coil.
  • magentic pulseUnit will pulse for 20 minutes (255 pulses) before resetting.
  • magentic pulseSlightly higher output pulse intensity.
  • magentic pulseNew soft carrying case for easy storage.

Unique Features:

  • New Hand-Paddle design. Our pulsing coil has been re-designed into a custom molded plastic enclosure complete with clear identification of the Bio-North (-) Magnetic Pole.
  • A unique circuit design allows The Magnetic Pulser to operate without the use of a Xenon flashtube allowing for maximum power delivery to the coil.
  • Fully Automatic. The MP6 will automatically charge and discharge - no manual pulsing required. An internal Digital Counter allows the MP6 to pulse approximately 20 minutes between resets.
  • LED light bar-graph. A light bar-graph consisting of five Green LED lights, illuminates sequentially giving visual indication of the MP6 charging up.
  • A Red LED light indicates either the unit has completed a 20 minute cycle of pulses, or an overload condition has occurred.
  • magentic pulseAUDIBLE output option. Unit beeps each time magnetic pulse is released to coil.
  • Operates from an AC-DC Wall Adaptor (included), or from a 12 Volt DC source like an automobile battery, appropriate solar panel, etc. (NOTE: We have adaptors that have blades for North America, Hong Kong, Europe, and Australia. Please specify when ordering.)
  • Extremely high magnetic power output. Generates maximum 42.18 Joules (Watt*Seconds) of energy through the use of a 600uF, 330VDC Custom Photoflash Capacitor. This then produces ~6,000 Gauss* (~6 kilo Gauss) magnetic field inside the coil. (For Gauss calculations, and an in-depth discussion on the electrical principles at play with an MP, click HERE.) 
    *
    Magnetic flux intensity follows the inverse square rule - the further you are away from the magnetic core, the faster the Gauss intensity drops off. At face of Magnetic Coil, the Gauss is ~6,000 Gauss as measured on an F.W. Bell Model 5080 Fluxmeter. Click HERE to see the actual Gauss reading at varying distances from the coil.
  • High-Frequency Custom Switch Mode Pulse-Width-Modulated (PWM) power supply allows for fast charges and a very lightweight unit. Our PWM power supply is a constant-current design.
  • Double-insulated practices used throughout to ensure the greatest electrical safety. Coil is completely enclosed in a custom-molded plastic Hand Paddle. No exposed wires or leads.
  • magentic pulseNew Professional Capacitor. We now have a Professional Custom Strobe type Capacitor designed specifically for our Magnetic Pulser. The manufacturer rates the capacitor at well over a 30 million (30,000,000) cycles of operation. Compare this with our earlier version model MP2 and MP3 which had a 250,000 cycle life, or to our MP1 which had a 85,000 cycle life, or even to photoflash based pulsers that have 5,000 - 10,000 life cycle. Click HERE to see our MP capacitors.
  • Fast charging cycle.
  • Overload Protection. Should an overload or fault condition occur in the charging section, a sensor will limit the current, then eventually shutdown the unit until the fault condition is removed.
  • Bio-North Magnetic Pole Polarity (-) or South-Seeking is clearly identified on one side of pulsing coil. This gives the user the choice of applying either Bio-North (-) or Bio-South (+) pole energy to the site.
  • Our Electrical Circuit Boards are GOLD Plated for extreme reliability and workmanship.
  • Compact and lightweight. MP6 unit weighs 3/4 Lbs. (0.3 Kg.), Magnetic coil weighs 1 Lb. (0.4 Kg.). Total shipping weight of complete MP6 with Wall Adaptor weighs ~3 Lbs. (~1.3 Kg.).
  • CE Certification

The Unit:

mag pulse

The Magnetic Pulser is housed in a new custom plastic enclosure. A pushbutton turns the Magnetic Pulser on and off. A series of Green lights indicates power is available and visually shows unit is charging. When turned on, the Magnetic Pulser will immediately begin to charge up. When fully charged, the stored energy of the capacitor is discharged into the pulsing coil. The Red light will flash indicating the charge has been released. The Magnetic Pulser will then begin another charge cycle.

Should an overload or fault condition occur in the charging section, the MP6 will shutdown until the fault condition is removed. The unit will beep and flash the Red light notifying the user.
After approximately 20 minutes of pulsing the MP6 will turn itself off. This helps prevent continuous operation should the MP6 be left on unattended.

The Magnetic Pulser is packaged in a soft carrying case for easy storage.

 


Line drawing of the MPG unit

Electronics:
The Magnetic Pulser is designed to the highest standards. We have improved on the original design with added features. Our electronic design is unique and efficient making the unit very reliable and powerful. Early designs required the use of a Xenon flashtube. We've completely re-designed The Magnetic Pulser from the ground up using the latest in electronic components. The result is a very powerful, reliable, rugged unit that transfers more energy to the output coil. In addition, we use double-insulation techniques to ensure the greatest in electrical safety. This is of extreme importance!

Specifications (as measured on a Tektronics TDS 210 Digital Real-Time Oscilloscope, and Wavetek AD105 Clamp-On RMS Ammeter)
·  Energy Storage Capacitor: 600uF, 450 Volts DC
·  Typical Energy Storage: 36.75 Joules (Watt*Seconds)
·  Maximum Energy Storage: 42.18 Joules (Watt*Seconds)
·  Typical Peak Charge Voltage: 350 Volts DC
·  Maximum Peak Charge Voltage: 375 Volts DC
·  Minimum Peak Current Discharge into Coil: 150 Amps RMS
·  Pulse Rise Time: <1.8 uS (microseconds) Click here to see the actual waveform
·  Pulse Duration: ~2.5mS (milliseconds) Click here to see the actual waveform
·  Main Coil Inductance: ~2.5mH (milli-henries)
·  Flux Density: 40,500 Ampere*Turns
·  Peak Magnetic Field Output: ~6,000 Gauss* (~6 kilo Gauss). For Gauss calculations, and an in-depth discussion on the electrical principles at play with an MP, click HERE.
*Magnetic flux intensity follows the inverse square rule - the further you are away from the magnetic core, the faster the Gauss intensity drops off. At face of Magnetic Coil, the Gauss is ~6,000 Gauss as measured on an F.W. Bell Model 5080 Fluxmeter. Click HERE to see the actual Gauss reading at varying distances from the coil.
·  Minimum number of Pulse Discharges 30 Million (30,000,000)
Each Magnetic Pulser comes complete with:

  • The Magnetic Pulser MP6 unit
  • Operating Instructions
  • One (1) International AC-DC Wall Adaptor (NOTE: We have adaptors that have blades for North America, Hong Kong, Europe, and Australia. Please specify when ordering.)
  • One (1) Soft Carrying Case
  • 2 Year Parts and Labor Warranty
  • CE Certification

carrying case


International Voltage (220/240 Volt AC 50 Hz Mains) Requirements:

  • The Magnetic Pulser ships with an International Wall Adaptor intended for any voltage from 110VAC 60 Hz (North America) to 220/240 Volt AC 50 Hz Mains (as found in International Countries). Thus, you can use your new Magnetic Pulser virtually anywhere in the world.
     
  • Additionally, the Magnetic Pulser may also be operated directly from a 12 Volt DC Battery like an automobile cigarette lighter. You will need to purchase an Adapter cord which plugs into the cigarette lighter and has a Centre Positive, 2.1mm Plug. Radio Shack® usually has these Adapters.

Options for Powering the Magnetic Pulser

In the event of a power outage here are some options for powering the Magnetic Pulser:

  1. The Magnetic Pulser may be operated directly from a 12 Volt DC Battery like an automobile cigarette lighter. You will need to purchase an Adapter cord which plugs into the cigarette lighter and has a Centre Positive, 2.1mm Plug, like from Radio Shack®.
  2. The Magnetic Pulser can be powered by a suitable solar panel. Keep in mind that most solar panel generators are used to re-charge a battery which in turn operates the unit. Therefore we suggest you use a solar panel (preferably a sealed Gel-Cel® type) to re-charge a 12 Volt DC automobile battery, then run the Magnetic Pulser directly from the battery. You will need to use a cord which has alligator clips on one end to attach to the battery terminals, and the appropriate Centre Positive, 2.1mm Plug on the other end to plug into the Magnetic Pulser. Be careful with polarity! This type of cord with alligator clips on one end is probably not readily available, therefore you will to need to buy a cord and cut off the end that normally goes into the cigarette lighter, and solder your own set of alligator clips. Use a black and red alligator clips so you ensure polarity is correct each time you connect the circuit.
  3. If you wish to operate the Magnetic Pulser directly from a solar panel you will need to use a 12 Volt DC output panel that is capable of supplying at least 2.5 Amps. The Magnetic Pulser's initial starting demands may require a higher output solar panel. That is why it is preferable to use a charged 12 Volt DC battery instead.

What about a Warranty?

The Magnetic Pulser has a full 2 Year Parts and Labor Warranty. A replacement custom main capacitor can be ordered through us.


How much is "The Magnetic Pulser"?

$395.00

Order Now

Brain Tuner

Order directly from Sota Instruments and receive an Extra 5% discount on your first purchase.You must click this link to enter the Sota ordering system: (or the buy button above)

http://www.sota.com/default.aspx?page=15&rtd=CA50070

In the event the link is not active, call Sota at 800-224-0242 and give the operator your Discount code number CA50070. Pass this Discount code along to your family and friends and they will also receive the 5% discount on their first purchase. Sota will process your credit card and ship the items directly to you from Canada. Charges will include item amount & shipping.

Sota Instruments Retailer Program

Become a Sota Retailer and earn a rewarding income, while helping your family, friends and community with the Sota Protocol. Information is available on the Sota Instruments website. We welcome the participation of health professionals and lay persons alike. You can access the Sota site through our link under Option 1. Please reference our I.D. - CA50070. You can also call Sota Instruments directly and ask them for complete details at
800-224-0242 or Email to - retailer@sota.com

 

 

   
   
   
The opinions stated are the views of Living From Vision and do not represent the opinion of SOTA Instruments. The SOTA units are consumer products designed for relaxation, well-being and to complement a healthy lifestyle. The SOTA units are not medical devices nor are they intended to diagnose, treat or cure any medical or health condition. The use, safety or effectiveness of the SOTA units, has not been approved by any government agency. Please consult a health practitioner for any medical or health condition. Results are not typical.
Disclaimer:
Information on this site should not be interpreted as a substitute for physician's evaluation or treatment by a healthcare professional, nor should it be used to provide or confirm a medical diagnosis. Some instruments are for Experimental Research Only and are clearly marked.
© 2006 Living From Vision. All Rights Reserved
Legal Disclaimer : Privacy Policy